CAN Bus Controller
CAN Bus Input / Output Controller
With 5 relay-based outputs and 5 analogue inputs, our CAN Bus Input / Output Controller offers exceptional flexibility for controlling low-power loads and interfacing with a wide range of sensors.
Additionally, it features full configurability through our accompanying software and the ability to seamlessly integrate into any CAN Bus Network.
The high-performance microcontroller and configurable CAN Bus speed and filters make this device a reliable and efficient solution for your control needs.
Applications
Passenger cars.
Building automation.
Truck and buses.
Industrial machine control.
Lifts and escalators.
Trains.
Maritime electronics systems.
Aircraft and aerospace electronics.
Energy storage systems.
Specifications
General specifications
Fully configurable via USB with a Windows application.
Firmware update over USB.
Power via USB or external power supply.
7 LEDs for indicating faults and activity:
Device status.
CAN Bus activity.
5 Outputs status.
4 pin pluggable terminal block (included with the device):
Power supply.
CAN Bus network.
5 relay based outputs connectors: 2 pin pluggable terminal block (included with the device).
5 Inputs: 2 pin and 5 pin pluggable terminal block (included with the device).
High performance 32 bits automotive microcontroller.
Small form factor: 108.5 x 91.5 x 30 mm (4.27 x 3.60 x 1.18 in).
CAN Bus
Supports Standard CAN 2.0A (11 bits ID) and Extended CAN 2.0B (29 bit ID).
Configurable CAN Bus speed (20, 33.333, 45, 50, 80, 90, 100, 250, 500, 800, 1000 kbps).
Configurable filter for logging the desirable CAN Bus messages based on the message ID.
Configurable 120 Ohms internal termination resistor.
High Electrostatic Discharge (ESD) handling capability on the Bus pins.
ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5 fully compliant CAN Bus transceiver.
AEC-Q100 qualified CAN Bus transceiver.
Relay Based Outputs
Contact rating: 5A 250VAC/30VDC.
Recommended continuous contact rating: 3A 250VAC/30VDC.
Up to 20 millions operations (empty load).
Up to 100,000 operations with a resistive load (3A 250VAC / 30VDC).
Maximum switching voltage: 250VAC / 125VAC @ 0.3A.
Maximum switching current: 5A.
Maximum switching power: 1250VAC / 150W.
Insulation resistance: 1000MΩ @ 500VDC.
Dielectric strength between coil and contacts: 3000VAC 1min.
Dielectric strength between open contacts: 1000VAC 1min.
Surge voltage: 6kV (1.2 / 50 µs).
Operate time: 10ms max.
Release time: 5ms max.
Shock resistance functional: 98 m/s2.
Shock resistance destructive: 980 m/s2.
Vibration resistance: 10Hz to 55Hz 1.5mm DA.
Inputs
5 single ended inputs.
1 connector 2 pin for ground signal.
Voltage input range: 0 to 3.3V.
12 bits, 805 µV resolution.
Accuracy: ±1.61 mV.
Maximum full scale error: ±0.5% (under 23±5℃, 45%～75%RH).
No pull-ups or pull-downs resistors on the inputs.
Over voltage and reverse polarity protection.
Electrical characteristics
Power from USB or from an external power supply.
Wilde range voltage supply input: from 7V to 28V DC.
Low power consumption:
Standby mode: 24mA @ 12V (0.29W).
Maximum: 75mA @ 12V (0.95W).
CAN Bus lines protection: 350 W Peak Power Dissipation per Line (8/20 sec Waveform).
Low Capacitance High−Speed CAN Data Rates.
Downloads
Documents
CAN Bus Input / Output Controller Specifications
CAN Bus Input / Output Controller Instructions Manual
Software
CAN Bus Input / Output Controller 1.00 - Installer
CAN Bus Input / Output Controller 1.00 - ZIP
Device Firmware Update
Drivers
Windows 10 - No drivers needed